Authorised Distributor · Jindal Hissar
Jindal Hissar Pipe Technical Data Sheet (TDS)
IS 1239 (Part I) & IS 3589 · Jindal Industries Pvt. Limited, Hisar
Technical data sheets issued by Jindal Industries Pvt. Limited, Hisar, for its ERW galvanised and black steel pipes, reproduced section by section with the signed PDFs available for download. Vijay Sales Corporation is an authorised distributor of Jindal Hissar pipes.
Reviewed by Punya Gupta, Vijay Sales Corporation · updated
IS 1239 · IS 3589
Two signed manufacturer TDS
15–150 NB
IS 1239 Medium & Heavy class
168.3–406.4 mm
IS 3589 OD range, Fe 330 / 410 / 450
Authorised
Jindal Hissar distributor, Delhi
Jindal Hissar IS 1239 (Part I) — Technical Data Sheet
Dimensions — Medium and Heavy class
| NB (mm) | 15 | 20 | 25 | 32 | 40 | 50 | 65 | 80 | 100 | 125 | 150 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| OD min (mm) | 21.0 | 26.5 | 33.3 | 42.2 | 47.9 | 59.7 | 75.3 | 88.0 | 113.1 | 138.5 | 163.9 |
| OD max (mm) | 21.8 | 27.3 | 34.2 | 42.9 | 48.8 | 60.8 | 76.6 | 89.5 | 115.0 | 140.8 | 166.5 |
| Thickness – Medium (mm) | 2.60 | 2.60 | 3.20 | 3.20 | 3.20 | 3.60 | 3.60 | 4.00 | 4.50 | 4.80 | 4.80 |
| Thickness – Heavy (mm) | 3.20 | 3.20 | 4.00 | 4.00 | 4.00 | 4.50 | 4.50 | 4.80 | 5.40 | 5.40 | 5.40 |
Dimensions — Medium and Heavy class
15 NB
OD min 21.0 · OD max 21.8 · Medium 2.60 · Heavy 3.20
20 NB
OD min 26.5 · OD max 27.3 · Medium 2.60 · Heavy 3.20
25 NB
OD min 33.3 · OD max 34.2 · Medium 3.20 · Heavy 4.00
32 NB
OD min 42.2 · OD max 42.9 · Medium 3.20 · Heavy 4.00
40 NB
OD min 47.9 · OD max 48.8 · Medium 3.20 · Heavy 4.00
50 NB
OD min 59.7 · OD max 60.8 · Medium 3.60 · Heavy 4.50
65 NB
OD min 75.3 · OD max 76.6 · Medium 3.60 · Heavy 4.50
80 NB
OD min 88.0 · OD max 89.5 · Medium 4.00 · Heavy 4.80
100 NB
OD min 113.1 · OD max 115.0 · Medium 4.50 · Heavy 5.40
125 NB
OD min 138.5 · OD max 140.8 · Medium 4.80 · Heavy 5.40
150 NB
OD min 163.9 · OD max 166.5 · Medium 4.80 · Heavy 5.40
Thickness tolerance: + not limited / −10%.Length: 4 to 7 m for all sizes (average length approximately 6 m).This sheet does not state weights.
Chemical properties
| Element | Maximum (%) | General observations (%) |
|---|---|---|
| C | 0.20 | 0.06 to 0.11 |
| Mn | 1.30 | 0.30 to 0.50 |
| S | 0.040 | 0.010 to 0.030 |
| P | 0.040 | 0.010 to 0.030 |
Chemical properties
C
Maximum (%): 0.20 · General observations (%): 0.06 to 0.11
Mn
Maximum (%): 1.30 · General observations (%): 0.30 to 0.50
S
Maximum (%): 0.040 · General observations (%): 0.010 to 0.030
P
Maximum (%): 0.040 · General observations (%): 0.010 to 0.030
Physical properties
| Test | Minimum requirement | General observations |
|---|---|---|
| Tensile strength (MPa) | 320 MPa | 380 to 430 MPa |
| Yield stress (MPa) | Not specified | 260 to 290 MPa |
| Elongation (%) | Up to 1″: 12% (min); above 1″: 20% (min) | 28 to 40% |
| Hydro test pressure | 51 kgs/cm² | |
Physical properties
Tensile strength (MPa)
Minimum requirement: 320 MPa · General observations: 380 to 430 MPa
Yield stress (MPa)
Minimum requirement: Not specified · General observations: 260 to 290 MPa
Elongation (%)
Minimum requirement: Up to 1″: 12% (min); above 1″: 20% (min) · General observations: 28 to 40%
Hydro test pressure
51 kgs/cm²
Galvanizing test
| Test | Requirement |
|---|---|
| Mass of zinc coating | Shall not be less than 360 g/m² |
| Uniformity test | The galvanized coating, when determined on a 100 mm long test piece in accordance with IS 2633, shall withstand five one-minute dips |
| Adhesion – bend | Galvanized tubes up to and including 50 mm nominal bore, when bent cold through 90° round a grooved former having a radius at the bottom of the groove equal to 8 times its outside diameter, shall not develop any crack in the coating |
| Adhesion – pivoted hammer | Adherence of zinc coating on tubes above 50 mm nominal bore shall be determined by the pivoted hammer test given in IS 2629 |
Galvanizing test
Mass of zinc coating
Shall not be less than 360 g/m²
Uniformity test
The galvanized coating, when determined on a 100 mm long test piece in accordance with IS 2633, shall withstand five one-minute dips
Adhesion – bend
Galvanized tubes up to and including 50 mm nominal bore, when bent cold through 90° round a grooved former having a radius at the bottom of the groove equal to 8 times its outside diameter, shall not develop any crack in the coating
Adhesion – pivoted hammer
Adherence of zinc coating on tubes above 50 mm nominal bore shall be determined by the pivoted hammer test given in IS 2629
Jindal Hissar IS 3589 — Technical Data Sheet
This sheet gives no size-wise thickness or weight table.
Tolerances
| Characteristic | Description |
|---|---|
| OD | ±0.75% |
| Ovality | Shall not exceed 1% of the specified outside diameter |
| Thickness | ±10% |
| Weight | For quantity per load of 10 tons: ±7.5% |
| Straightness | Max 1/600 of pipe length |
| Bevel angle & root face (if applicable) | Bevel angle 30° +5° / −0°; root face 1.6 +0.8 mm |
Tolerances
OD
±0.75%
Ovality
Shall not exceed 1% of the specified outside diameter
Thickness
±10%
Weight
For quantity per load of 10 tons: ±7.5%
Straightness
Max 1/600 of pipe length
Bevel angle & root face (if applicable)
Bevel angle 30° +5° / −0°; root face 1.6 +0.8 mm
Chemical composition (max, %)
| Grade | Fe 330 | Fe 410 | Fe 450 |
|---|---|---|---|
| C | 0.16 | 0.20 | 0.25 |
| Mn | 1.20 | 1.30 | 1.20 |
| S | 0.040 | 0.040 | 0.040 |
| P | 0.040 | 0.040 | 0.040 |
| CE | — | 0.45 | 0.45 |
Chemical composition (max, %)
Fe 330
C 0.16 · Mn 1.20 · S 0.040 · P 0.040
Fe 410
C 0.20 · Mn 1.30 · S 0.040 · P 0.040 · CE 0.45
Fe 450
C 0.25 · Mn 1.20 · S 0.040 · P 0.040 · CE 0.45
Mechanical properties (min)
| Grade | Fe 330 | Fe 410 | Fe 450 |
|---|---|---|---|
| T.S. (MPa) | 330 | 410 | 450 |
| Y.S. (MPa) | 195 | 235 | 275 |
| Elongation (%) | 20 | 18 | 15 |
Mechanical properties (min)
Fe 330
T.S. 330 · Y.S. 195 · Elong. 20
Fe 410
T.S. 410 · Y.S. 235 · Elong. 18
Fe 450
T.S. 450 · Y.S. 275 · Elong. 15
Other parameters
| Characteristic | Description |
|---|---|
| Product analysis | No chemical analysis is required for identified material received with test certificate and covered under BIS certification scheme |
| Hydrostatic test | Hydrostatic test shall be applied without leakage through the weld seam or the pipe body. |
| Heat treatment | NA |
| Flattening test | Flattening rings not less than 40 mm in length cut from the ends of the selected tubes shall be flattened cold between parallel plates with the weld, if any, at 90° (point of maximum bending) in accordance with IS 2328. No opening shall occur by fracture in the weld area until the distance between the plates is less than 75% of the original outside diameter of the tube, and no cracks or breaks in the metal elsewhere than in the weld shall occur until the distance between the plates is less than 60% of the original outside diameter. |
| Galvanizing (if applicable) | Mass of zinc coating 360 g/m² min; uniformity: 5 dips of one minute each; adhesion: pivoted hammer test |
Other parameters
Product analysis
No chemical analysis is required for identified material received with test certificate and covered under BIS certification scheme
Hydrostatic test
Hydrostatic test shall be applied without leakage through the weld seam or the pipe body.
Heat treatment
NA
Flattening test
Flattening rings not less than 40 mm in length cut from the ends of the selected tubes shall be flattened cold between parallel plates with the weld, if any, at 90° (point of maximum bending) in accordance with IS 2328. No opening shall occur by fracture in the weld area until the distance between the plates is less than 75% of the original outside diameter of the tube, and no cracks or breaks in the metal elsewhere than in the weld shall occur until the distance between the plates is less than 60% of the original outside diameter.
Galvanizing (if applicable)
Mass of zinc coating 360 g/m² min; uniformity: 5 dips of one minute each; adhesion: pivoted hammer test
Need these documents for a consultant or client submittal?
Tell us the sizes and quantity. We will send a quotation along with the documents you need.
Frequently Asked Questions
Is there a technical data sheet for Jindal Hissar IS 1239 pipes?
Yes. Jindal Industries Pvt. Limited, Hisar, issues a technical data sheet for IS 1239 (Part I) pipes covering Medium and Heavy class from 15 NB to 150 NB. The signed sheet can be downloaded on this page.
What hydro test pressure does the Jindal Hissar IS 1239 TDS state?
51 kgs/cm².
What is the minimum zinc coating on Jindal Hissar GI pipes as per the TDS?
The mass of zinc coating shall not be less than 360 g/m².
What is the wall thickness of Jindal Hissar 100 NB pipe in Medium and Heavy class?
4.50 mm in Medium and 5.40 mm in Heavy, with an outside diameter of 113.1 to 115.0 mm, as stated on the IS 1239 sheet.
Which grades are covered in the Jindal Hissar IS 3589 TDS?
Fe 330, Fe 410 and Fe 450, for pipes from 168.3 mm to 406.4 mm outside diameter.
What are the minimum mechanical properties of Jindal Hissar IS 3589 Fe 410 pipe?
Tensile strength 410 MPa, yield strength 235 MPa and elongation 18%, as stated on the sheet.
What straightness tolerance does the Jindal Hissar IS 3589 TDS give?
Maximum 1/600 of the pipe length.
How do I get Jindal Hissar pipes with documents for a project submittal?
Use the request form on this page or WhatsApp +91 9999889008 with sizes, class and quantity. Vijay Sales Corporation is an authorised Jindal Hissar distributor in Delhi.
Request a Quote & Documents — Jindal Hissar Pipes
Send your requirement. We reply on WhatsApp with rates and the documents you ask for.